Single metal fuel banjo for Dellorto carbs. Fuel filter FUA60888 sits inside this part and makes seal to carb

Also known as Guzzi ref. 10934600 and Ducati ref. 075527250

 More than 5 in stock

 13934600 GU13934600 13 93 46 00
 1393 4600 1393.4600 13.93.46.00

Also fits Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 600 SL Pantah, Ducati 750/900 SS Koewe, Ducati 860/900 GTS, Ducati 900 Darmah, Ducati 900 MHR, S2, Ducati 900 MHR-I, Ducati 1000 MHR-2,S2

Pod type air filter for increased air flow

Made from a high performance twin layer foam this K & N type air filter is designed to offer improved and unrestricted airflow whilst offering adequate filtration. Washable and reusable (use hot soapy water). Best run dry for road. Fits VHB 29, VHB 30, PHBH28 and PHBH30 Dellorto carbs. You may find that a 5-10% increase in main jet size helps to make the most of the increased air flow with this filter

 This part is available by special order, request a quote

Dellorto needle valve and seat for PHF 30 carbs

 2 in stock

Dellorto needle valve

Needle valve kits not available for the VHB 30 as the seat is part of the carb body

 1 in stock

Dellorto V9 slide needle for VHB 30 carbs

Standard needle clip position is 2nd groove from top

 This part is due back in stock soon, call 01484 841395 to reserve yours

 13937700 GU13937700 13 93 77 00
 1393 7700 1393.7700 13.93.77.00

Dellorto V5 slide needle for VHB 30 carbs. The original V9 needle has limited availability and this is the closest alternative. Drop the V5 needle by one groove to simulate the V9 needle

The V5 needle has also been discontinued so stocks are limited. Standard needle clip position is 2nd groove from top

 1 in stock

 13937700 GU13937700 13 93 77 00
 1393 7700 1393.7700 13.93.77.00

Dellorto kit containing mixture screw, o ring, spring and washer

For most VHB, PHBH, PHF and PHM carbs, check length before ordering, FUA60854 is alternative screw

 3 in stock

 13936600 GU13936600 13 93 66 00
 1393 6600 1393.6600 13.93.66.00

90 degree inlet sleeve from airbox to carb

Airbox inlet elbow. Use SSA32957 to clamp to carb

 2 in stock

14114460-z 14114460 GU14114460 14 11 44 60
 1411 4460 1411.4460 14.11.44.60

Special Inlet rubber with HT lead guide for late Dellorto PHM carbs with a inlet stub OD of 46mm

Use clip SSA45970
This part will only fit late PHM40 carbs with 46mm inlet stubs, we recommend measuring your carbs before ordering

 1 in stock

Plastic inlet manifold, replaces unavailable aluminium manifold. Suitable for PHF 30 carb conversions on models previously fitted with VHB30 carbs. Contains inlet manifold, gasket, O rings, clip and M6 bolts to secure to head. Carb mounts direct to this manifold (no inlet manifold rubber required)

Note that on models with M8 inlet manifold bolts and standard heads (T3, 1000 SP) it will be necessary to drill out the manifold bolt holes from 6mm to 8mm to reuse your existing bolts. Can be used to replace PHF30 inlet manifolds 17116265 and 17116365 which are no longer available. These manifolds exit the heads at a different angle to VHB manifolds and in some cases you may need to modify side panels to allow clearance for air filters

 1 in stock